整体移动喷漆房温湿度控制介绍
(1)湿度控制的原理是在集中烘房。如果没有冷空气，只有加热室和烟室的热空气在里面循环。如果有冷空气进入，在除湿门灵活控制的情况下，只要控制冷空气进入门的大小，除湿门必然会自行打开，房间内的潮湿空气就会被排出。此时通过除湿门排出。
(1) The principle of humidity control is in a centralized drying room. If there is no cold air, only the hot air from the heating chamber and smoke chamber circulates inside. If cold air enters, with flexible control of the dehumidification door, as long as the size of the cold air inlet is controlled, the dehumidification door will inevitably open on its own, and the humid air in the room will be discharged. At this time, discharge through the dehumidification door.
(2)温度控制原理根据燃料燃烧与燃料和助燃空气量的关系，通过控制助燃空气量、煤燃烧量和烟气排放量，控制燃烧强度，控制温度加热和喷房的控制。
(2) The principle of temperature control is based on the relationship between fuel combustion and the amount of fuel and combustion air. By controlling the amount of combustion air, coal combustion, and flue gas emissions, the combustion intensity is controlled, and the temperature heating and spray chamber are controlled.
新鲜空气从整体移动喷漆房前部吸入喷漆操作区，喷漆时气流均匀环绕工件。喷漆雾不会飞出喷漆室范围。过喷的漆雾在负压作用下被吸入油膜漆雾净化器，先经过二流油膜的截留和附着，少量漆雾被油气分离器分离出来排放达到国家标准，漆雾去除率可达95%。
Fresh air is sucked into the spray painting operation area from the front of the mobile spray painting room, and the airflow evenly surrounds the workpiece during spray painting. Spray paint mist will not fly out of the paint booth area. The overspray paint mist is sucked into the oil film paint mist purifier under negative pressure. It first passes through the interception and attachment of the secondary oil film, and a small amount of paint mist is separated by the oil and gas separator and discharged to meet national standards. The paint mist removal rate can reach 95%.
整体移动喷漆房技术特点
Technical characteristics of the overall mobile paint spraying room
整体移动喷漆房应用粒子撞击、惯性分离、废气过滤等技术原理。它利用某种矿物油形成的均匀流动的油膜来收集漆雾。采用矿物油作为捕集漆雾的介质，解决了以往用水作为介质的问题。介质造成的诸多弊端，在设备中净化后可循环使用。该净化装置设计合理，效果明显，无二次污染，设备使用寿命长。
The overall mobile paint spraying room applies technology principles such as particle impact, inertial separation, and exhaust gas filtration. It uses a uniformly flowing oil film formed by a certain mineral oil to collect paint mist. Using mineral oil as the medium for capturing paint mist solves the problem of using water as the medium in the past. The many drawbacks caused by the medium can be recycled after purification in the equipment. The purification device is designed reasonably, with obvious effects, no secondary pollution, and a long service life of the equipment.
整体移动喷漆房的制造方法
Manufacturing method of overall mobile paint spraying room
移动门架立柱和横梁骨架采用40601.5镀锌方管焊接立柱门架结构。龙门立柱横梁采用1.5mm厚镀锌板喷涂。移动龙门架底部两侧安装1.5KW驱动电机、减速机和配电轴。动力分配两端安装主动链轮，动力通过链条传递到门架底部的主动移动轮上。左右各有1组驱动轮，每组有2个驱动轮。活动房伸缩支架由活动立式支架、横梁和活动滑轮组成。竖向支撑采用60401.5矩形管焊接成矩形框架结构，尺寸为L3500W350，横撑每隔750mm抽出。横梁做成L12700W350的矩形框架结构，每750mm拉一次横撑，横撑之间用40201.5的矩形管做斜撑，12组垂直支撑和梁结构。尾部一套为固定支架，一套为移动支架。立式支架与横梁内壁贴PVC布，镀锌压条做压板，支架内肋与横梁内肋用斜撑连接消除移动框架的横向挠度变形。本设备主要为喷漆作业提供专用环境，满足喷漆作业对温度、湿度、光照、空气洁净度等方面的要求。移动式喷漆房是一种环保型涂装设备。
The mobile gantry column and crossbeam framework adopt a 40601.5 galvanized square tube welded column gantry structure. The crossbeam of the gantry column is sprayed with 1.5mm thick galvanized sheet. Install 1.5KW drive motors, reducers, and distribution shafts on both sides of the bottom of the mobile gantry. Active sprockets are installed at both ends of the power distribution, and power is transmitted to the active moving wheels at the bottom of the gantry through the chains. There is one set of drive wheels on each side, with two drive wheels in each group. The telescopic bracket for the activity room consists of a movable vertical bracket, a crossbeam, and a movable pulley. The vertical support adopts 60401.5 rectangular pipes welded into a rectangular frame structure, with a size of L3500W350, and the horizontal braces are pulled out every 750mm. The cross beam is made of L12700W350 rectangular frame structure, and the cross brace is pulled every 750mm. 40201.5 rectangular tubes are used between the cross braces as slant support, and 12 groups of vertical braces and beam structures are used. One set at the tail is a fixed bracket, and the other set is a mobile bracket. The vertical support and the inner wall of the beam are pasted with PVC cloth, the galvanized batten is used as the pressing plate, and the inner ribs of the support and the beam are connected with slant support to eliminate the lateral deflection deformation of the moving frame. This equipment mainly provides a dedicated environment for spray painting operations, meeting the requirements of temperature, humidity, lighting, air cleanliness, and other aspects for spray painting operations. Mobile paint booth is an environmentally friendly painting equipment.
鲁公网安备 37142502000144号